Відео

Thumbs up for driving a Saab!

I enjoyed your video. Approximately how much did a job like this cost, all parts and labor?

Totally unnecessary. Just use liquid glads head gasket repair. Saved me 4k!

A Just did a 2017 Ford Fusion Hybrid engi e swap. Made à HD rolling table similar to what you used. Way easier swapping wiring, parts and lines on the table.

Great saying "keep it out of the cabbage"

My uncle and aunt have the same car but a 1990

At least the cab of the truck didn’t have to be removed

I need to install these on my 9-5. What about cutting the bolt on passenger side instead of lowering the subframe? Also, I have high negative camber so once these are installed, is it just a matter of threading out the nut closest to the wheel until it pushes the wheel out? Thank you

Both of MY laches BROKE on my CASE 😢

Would the sensor be in the same spot on a 2006 Ford 500 limited? Thx!

Even new parts fail not your fault.

It is a 1973 model

pretty boy lloyd you should just say what ya gotta say instead of bringin every tom dick and harry into it

Where is the best place I can find all new rubber seals and belts for a 1986 Honda gold wing Interstate?? I am buying one tomorrow with a clean Arizona title. The guy fired it up, it has a misfire on one of the cylinders. And a slight backfire. I am thinking it sounds like a carb issue. It has 28,047 original miles on it. I want to bring her back to her full potential.

I can hear that knocking all the way from England.😮

Stanley uses Nickel plating not chrome. Nickel is much harder than chrome plating and holds up better on tools.

Yuh 😵

7:15 he can’t drive

Looks like someone finally sold the building/it's contents before 11 mos ago. 513 Dustin Tavern Rd on maps- all the cars are gone, different cars & equipment in the side & back lot. Can't see the Mustang through the window. Hope you got your soccerball wheels from that Sonnet!

Only 9 minutes in so you may end up answering this but before I forget I’ll ask. Have you ever tried a the stud attachment cleaners? They look just like the the grinding disc but it comes with a hole in the center of the disc so that you can go around each stud on the hub. Haven’t met a tech that has used them yet but curious as to if it’s worth the purchase or not

Not a Cimmaron, a Sedan de Ville.

Hi…where did you purchase the Flex light kit? Thanks

MICHELTFDSAKKKKJRGH

Can confirm this works on a 2018 VW Tiguan. Thank You so Much!!!!!

Were you at these days?

Hope all is well. Miss your videos

I wouldn't do my truck like that. Therefore I would not do someone else's truck like that. Why repair the bedside just to set it up to rust out again?

After all these years is that '79 Thunderbird still there?

You came out smoking like a bandit that is awesome it is beautiful I have a 1977 GW

Here because of the WGBH big dig podcast. Fascinating stuff

Your not making videos any more .Your videos were great hope all is well!

0:00 smoothest intro ever 💀

This is why I left this industry. 500k in tools and no pay.and long days on the same car.yea yall can have that crap.

Saab sonett video with subtitle: ua-cam.com/video/4gEvRgZ3OLw/v-deo.html

Had my TT for a few mouths now had a coolant leak n now I know everything I need to know from this vid this guy is a g

Lloyd "the needle scaler" Christmas

Hello Amesie's Corner! Can I use your video in my video plus comments to help people learn lessons so they can drive safer? I'll put your name on the screen, thank you for reading.

Need this done on my 4.0 4Runner. How much did you charge for this job? Definitely can’t do this job myself. Great video.

That was me that posted that. I can't believe it's been over 8 years since then.

Where is that at

Where have you been no more videos

Good video overlaying makes it easier and probably stronger

When's the next video

I got a 2006 Cadillac STS 3.6 that I’m pulling the engine in the drive way out the top and it’s a pain in the ass all ready got the new engine.I’m to old to be doing this shit I’ve been a mechanic all my life .started in the 80s cars to day are over engineered peace’s of shit. I’d take a carbureted 302 or 350 or 327 or 351 any day.

Put conventional oil in m54 or any BMW? Did you bump your head?

Yes there were 2010 Solstices produced. About 10 as I recall. Like always, the early cars in a model year came out late the year before. I don't know what colors were produced, how many Base, GXP, or Coupes.

He should have researched more. He got more wrong than right. I own 2 Solstices and love them both. The Base competes well with Miata in every important way (as originally intended by GM). The GXP is scorcher fast in all gears. Its HP to displacement ratio remains even today the largest of any GM engine ever mass produced. Saab? Why?

How did they hold up?

Might have been a good restoration project when he first got it 35 years ago. Any chances of that are decades over at this point.

I am sad to hear Skateland closed. I miss Haverhill, I've been in VT for almost 30 yrs